Creates a pulse on output (Aon) at a preset time.
A snooze function is also integrated.
In addition to individual days of the week, you can define your own alarm times for the operating modes "Public Holiday", "Vacation", and "School Holidays/Day off".
For the operating modes either corresponding operating times must be created or the output of the respective operating mode must be activated via a program logic.
Table of Contents
Inputs↑
| Abbreviation | Summary | Description | Unit | Value Range |
|---|---|---|---|---|
| Ca | Confirm alarm | - | 0/1 | |
| S | Start snooze timer | Pulse sets output (Buzzer) to 0 and starts snooze timer for the duration of parameter (Sd). Another pulse during an active snooze timer restarts the timer. | - | 0/1 |
| DisA | Disable alarm entries | Disables all alarm entries when On. | - | 0/1 |
| Tg | Toggle | Enables / disables the alarm entry 'Default alarm'. A pulse during an active alarm ends the alarm. | - | 0/1 |
| Set | Set alarm time for default alarm | Defined by minutes past midnight (E.g. 360 min = 06:00am) | min | 0...1439 |
| Rtd | Reset to default | Resets parameters and settings of the block to the default values as specified in the block preset. | - | 0/1 |
| Off | Off / Lock | Pulse (< 200 ms): Outputs are reset / switched off. Pulse (> 200 ms): Block is locked. Dominating input. Pulse (> 500 ms): The name of the connected sensor is used in the user interface. | - | 0/1 |
Outputs↑
| Abbreviation | Summary | Description | Unit | Value Range |
|---|---|---|---|---|
| Aon | Pulse on alarm start | - | 0/1 | |
| Aoff | Pulse on alarm end | - | 0/1 | |
| Buzzer | Buzzer | ON when alarm sound is active. OFF during snooze time. | - | 0/1 |
| A | Alarm | ON when alarm is active. | - | 0/1 |
| Pa | Pre-alarm | Outputs a pulse before the alarm. Start time set via parameter (Pat). | - | 0/1 |
| Rst | Remaining snooze time | s | 0...∞ | |
| Da | Default alarm state | On, when alarm entry 'Default alarm' is enabled. | - | 0/1 |
| Tna | Time of next alarm | Outputs date and time of the next alarm | - | - |
| API | API Connector | Intelligent API based connector. Can link several functions between devices and blocks. API Commands | - | - |
Parameters↑
| Abbreviation | Summary | Description | Unit | Value Range | Default Value |
|---|---|---|---|---|---|
| Rem | Remanence input | Remanence input: If active, the function block retains its previous state after a Miniserver reboot. The state of the function block is saved: – When saving to the Miniserver – At a planned reboot – Before a backup – Once per hour The data is saved on the SD card. | - | 0/1 | 0 |
| MaxA | Maximum alarm duration | Ends alarm after set time. If setting "Confirmation required" is activated, the snooze timer starts after the alarm duration has expired. | s | 0...∞ | 120 |
| Pat | Pre-alarm time | Time that the pre-alarm (Pa) is started before the alarm. | s | 0...∞ | 180 |
| Sd | Snooze duration | Snooze duration until the alarm sound is restarted. | s | 60...1800 | 300 |
| Bri | Touch Nightlight display brightness inactive | This parameter is only visible in certain configurations. | % | 0...100 | 0 |
| Bra | Touch Nightlight display brightness active | This parameter is only visible in certain configurations. | % | 0...100 | 50 |
| As | Alarm sound (Touch Nightlight) | 1: Deep 4-way beep 2: High 4-way beep 3: Deep 2-way beep 4: High 2-fold beep 5: Siren This parameter is only visible in certain configurations. | - | 1...5 | 1 |
| Asv | Alarm sound volume (Touch Nightlight) | This parameter is only visible in certain configurations. | % | 5...100 | 100 |
| Asf | Alarm sound fade-in (Touch Nightlight) | 1 = Alarm sound fades in for the duration of 60 seconds. 0 = No fade-in This parameter is only visible in certain configurations. | - | 0/1 | 0 |
Properties↑
| Summary | Description | Default Value |
|---|---|---|
| Alarm settings | Edit Alarms | - |
| Acknowledgement required | After the alarm the snooze timer starts automatically until it is acknowledged | - |
Set alarm time↑
Alarm times can be added using the plus button and removed using the X button.
The alarm time can be set directly in the settings menu, but it can also be added via the user interface
