The LOXONE Wall Display 10" is a permanently installed, surface-mounted interface for central locations in a building. The touch-based interface allows control of lighting, shading, climate, audio, and system functions.
Table of Contents
Mounting↑
Attach the supplied plastic mounting frame to a flat surface or a flush- or surface-mounted box. For flush-mounted installations, a 100 x 100 mm flush-mounted box is recommended, as it provides suitable mounting points and sufficient space for LAN or Wi-Fi adapters. This is not required when using Tree Turbo. Without a flush-mounted box, the mounting frame must be secured directly to the wall, for example using dowels.
A device box is not strictly necessary but simplifies storing the connection cables behind the device and creating a reserve loop.
 | Recommended mounting height: 1.45 m |
Connect the power supply (orange/white terminal) and select the desired data connection: Tree Turbo (green/white terminal) or USB-C. USB-C requires adapters, sold separately:
LAN: USB-C -> Ethernet adapter
Wi-Fi: USB-C -> USB-A adapter -> Wi-Fi dongle
Place the display onto the mounting frame and slide it down until it clicks into place.
Commissioning↑
For commissioning, the device must be supplied with power. The further setup depends on the used interface via Tree Turbo or LAN/Wi-Fi.
Alternatively, the Wall Display 10" can be connected directly to the Miniserver on the display.
Via Tree Turbo
A connection to the Miniserver Compact or Audioserver must be established via the Tree Turbo interface.
Then follow the pairing procedure on the Tree Turbo Interface.
Via Network
Connect the device to the network via LAN or Wi-Fi.
After a successful network connection, the device can be added using the Network Device Search in LOXONE Config.
Programming↑
When a Wall Display 10" is added, a user is automatically created for this device. Permissions for this user can be assigned via the User and Rights Management. Functions requiring elevated permissions, such as expert settings or searching for Air/Tree devices, are disabled by default.
In the properties window, the app's display appearance can be customized:
The display is programmed and further set up using the Wall Display 10" function block:
Sensors↑
| Summary | Description | Unit | Value Range |
|---|---|---|---|
| Brightness | Measured Brightness Value | Lux | ∞ |
Actuators↑
| Summary | Description | Unit | Value Range |
|---|---|---|---|
| Backlight | Dimmer value of orientation light | % | 0...100 |
| API Connector | Intelligent API based connector. API Commands | - | - |
| Orientation light | Digital | 0/1 |
Diagnostic Inputs↑
| Summary | Description | Unit | Value Range |
|---|---|---|---|
| Online Status Wall Display 10 | Indicates whether the device can be reached by the Miniserver. Diagnostics for Air devices Diagnostics for Tree devices Diagnostics for Extensions | Digital | 0/1 |
Properties↑
| Summary | Description | Value Range | Default Value |
|---|---|---|---|
| Serial Number | Specifies the serial number of the device. | - | - |
| Monitor Online Status | If checked, you will be notified via System Status or the Mailer if the device is no longer available or goes offline. | - | - |
| Miniserver | Miniserver this device is paired to | - | - |
| Network Address | IP address or hostname of the device on the local network | - | - |
| Default Screen | Specifies which screen should be displayed upon app launch or when Ambient Mode is re-activated. | - | - |
| Screensaver | Specifies the appearance of the Screensaver. Screensaver activates after end of presence and end of user interaction. | - | - |
| User interaction overrun duration | Display remains active for this duration after last user interaction. | 30...50000000 | 60 |
| User | User assigned to this device. | - | - |
| Multi-Miniserver Mode | Allows the Wall Display to switch between different Miniservers while remaining paired. The device is not limited to a single Miniserver and can be used with multiple Miniservers. | - | - |
| Device Configuration | Edit device settings. A connection to the Miniserver is required. | - | - |
Safety Instructions↑
Installation must be carried out by a qualified electrician in accordance with the applicable regulations.