The Touch Nightlight Air features five touch points to control the most important functions of a room. It is based on the Loxone switch standard.
The device is equipped with an RGBW night light and a display that shows the time and allows the setting of the alarm clock. The additional sixth touch point can be freely programmed. The device is powered by a Micro USB power supply.
 | On the Touch Nightlight gold, the T5/3 button cannot be activated by touching the segment display area. The gold surface is slightly conductive, which interferes with the capacitive touch sensor. As a result, touch inputs within the segment display cannot be reliably detected. |
Datasheet Touch Nightlight Air White / Gold
Datasheet Touch Nightlight Air phase out
Datasheet Touch Nightlight Air Gen.1
Table of Contents
- Mounting
- Commissioning
- Touch Usage
- Programming
- Alarm Clock Function
- Inputs, Outputs, Properties
- Safety Instructions
- Documents
Mounting↑
Place the device in the desired location and connect the supplied Micro USB power adapter to the back of the device.
Commissioning↑
In delivery state, pairing mode will be active after the power supply has been established. This is indicated by the light flashing red/green/orange.
Then follow the pairing procedure on the Air Interface.
To activate the pairing mode manually, hold down the pairing button for at least 5 seconds after establishing power supply. The pairing button is button 7, located at the bottom.
Touch Usage↑
Activate/Deactivate Alarm: Short press T7 (display blinks when active).
Set Alarm Time: Press and hold T7 for 3 s (display flashes) and use T1/T2/T4/T5 to adjust hours and minutes.
Confirm: Short press T7 (display blinks when active).
The upper middle touch point (T6) is a freely assignable input.
You could use it to activate Night Mode or arm the burglar alarm, for example
Programming↑
The Touch Nightlight Air is controlled via the Alarm Clock block. If the Alarm Clock block is linked to a Touch Nightlight, a static alarm entry is displayed for it. It is best to use Auto Configuration for the initial setup. This will automatically configure the Nightlight and Alarm Clock together.
Alarm Clock Function↑
The lower button on the Touch Nightlight Air is used to activate and deactivate the alarm. The status LED indicates whether the alarm is currently active.
To snooze an active alarm, press any button other than the lower button. This is confirmed by a single pulse of the lower LED.
Setting the Alarm Time
To change the alarm time, hold down the lower button until the display shows the current alarm time. Use the left and right buttons to adjust the time. Press the lower button again to confirm.
Time Format
When the 12-hour time format is used, a dot on the display indicates whether the time shown is AM or PM. The time format can be changed in the project settings in Loxone Config.
Display Brightness
The display has two brightness levels: active and inactive. After 20 seconds without interaction, the display switches to the lower inactive brightness level. Both levels can be adjusted via the app or in Loxone Config on the assigned Alarm Clock block. If desired, the display can be fully turned off during inactivity.
Temperature Display
If the temperature output of the Touch Nightlight Air is used in Loxone Config, the display alternates every 5 seconds between the current time and the current temperature during normal operation. If the output is not connected, only the current time is displayed.
Sensors↑
| Summary | Description | Value Range |
|---|---|---|
| T5 | Combined input for the 5 touch points according to the Loxone Switch Standard. | ∞ |
| Input 6 | This input is controlled via the upper middle button on the Touch Nightlight Air. | 0/1 |
Actuators↑
| Summary | Description | Unit | Value Range |
|---|---|---|---|
| Temperature | Output to show a temperature on the display | ° | -99...999 |
| Smart actuator RGBW | Output for controlling the integrated RGBW night light | - | 0...100 |
| Status LED | Output for controlling the status LED | - | 0/1 |
| API Connector | Text | - |
Diagnostic Inputs↑
| Summary | Description | Unit | Value Range |
|---|---|---|---|
| Online Status Touch Nightlight Air | Indicates whether the device can be reached by the Miniserver. Diagnostics for Air devices Diagnostics for Tree devices Diagnostics for Extensions | Digital | 0/1 |
Properties↑
| Summary | Description | Default Value |
|---|---|---|
| Monitor Online Status | If checked, you will be notified via System Status or the Mailer if the device is no longer available or goes offline. | - |
| Serial Number | Serial number of Air device. Automatic pairing can be enabled on the Air Base. Automatic pairing can be enabled on the Airbase for a set time. | - |
| Actuator Type | Use device with Standard Actuator(s) or Smart Actuator(s) Smart Actuators support dynamic fade times and can only be used with the Lighting Controller. | - |
| Show Button 1 | Show individual button | - |
| Show Button 2 | Show individual button | - |
| Show Button 3 | Show individual button | - |
| Show Button 4 | Show individual button | - |
| Show Button 5 | Show individual button | - |
| Audible acknowledgement | Audible acknowledgement on button press | - |
| Button Behaviour | Specifies the behavior when a button is pressed. Pulse: Sends a pulse on rising edge OnOff: Sends ON on rising edge and OFF on falling edge, used for long click Automatic: Sends a pulse on rising edge for buttons 1 & 4 (shading) and 3 (lighting). Sends ON on rising edge and OFF on falling edge for buttons 2 & 5 (music) to enable volume up/down via long press | - |
Safety Instructions↑
Ensure that the device is protected from water.
Documents↑
Datasheet Touch Nightlight Air White / Gold
Datasheet Touch Nightlight Air phase out
Datasheet Touch Nightlight Air Gen.1