Commissioning Loxone Nano IO Air

Initial steps to use Loxone Nano IO Air

Loxone Musterkoffer

Technical Data

  • Power supply: 110-230V AC, 50 / 60Hz (hedge max 10A)
  • 2 digital outputs 5A at 230V with a power factor of 1 (Mains voltage only!)
  • 6 digital inputs 24VDC (SELV)
  • 24V DC output for sensors (SELV), max. 1W
  • based on Loxone Air Technology
  • Frequency: 868 MHz (SRD Band Europe), 915MHz (ISM Band Region 2)
  • Standby power consumption: 0.5 W typ.
  • Dimensions: 53 x 53 x 31mm
  • Onboard microprocessor
  • Ambient temperature: 0 ... 35 ° C
  • Max. Relative humidity: 95% (non-condensing)
  • Protection class: IP20
  • Mode of operation: Type 1 (EN60730-1)
  • Insulation tested at: 2.5kV (EN60730-1)
  • Pollution degree: 2

Getting Started

Before being able to use the Loxone Nano IO Air, it must be learnt-in. To do this the Nano IO Air needs to be in learing mode.

Initial setup:

When the Nano IO Air is powered up for the first time, the learning mode will start automatically.

Re-learning in process:

To re-lean in the Loxone Nano IO Air, simply press and hold the learn button for at least 5 seconds. The Loxone Nano IO Air is now back in the learning mode.

The learn button is located on the bottom left of the underside of the Nano IO Air.

Once the unit is in the learning mode, the status LED flashes red-green-yellow in sequence.
In Loxone Config, activate the Loxone Air Monitor. To do this click on the Air Base Extension and then tick the checkbox "Start and Dispaly Air Monitor".

Now click on 'Start Search'. All Air devices in learning mode will be listed.

Now select the device you want to learn in, enter a name and click on "Create Device".


The device will now be listed in the Periphery tree.

The following items are now available for configuration as part of the device itself:

  • Online Status
  • CPU temperature
  • 6 digital inputs
  • 2 digital outputs

replace device

If a device has been replaced you need to update the serial number. You can easily do that in the Air Monitor in Loxone Config.

  • mount the new device and activate the power supply or insert the battery
  • search for air devices in learn-mode (as shown in the "getting started" section)
  • highlight the new device and choose the device you would like to replace in the drop-down menu

Finally press "Replace Device" and save your program in the Miniserver. The device has now been replaced.

Loxone Touch and Touch Pure for Nano



The Touch for Nano and Touch Pure for Nano are expansion modules for the Nano IO Air and provides 5 touch surfaces.






If you are using a Loxone Touch for Nano or Touch Pure for Nano, don't forget to select it in the properties of the Nano IO Air.



The touch points may be used in Loxone Config as digital inputs.


Press-and-Hold function will be supported by next update.


The Air devices will run their update automatically in the background, and they will function throughout the update. 

If the Air devices are updating when the Miniserver and the Air Base Extension are rebooted then the Air devices will restart the update from the beginning after the reboot. 

The update can take up to an hour so do be aware of this! You can check the version of the devices by looking in Device status. Click on the Miniserver tab and then click the Device status button once.

Funk Schaltaktor - Loxone


The Nano IO Air is equipped with two relays. Each with a maximum switching capacity is 5A at230V with cosφ=1.

NOTE: Please note that the relays are not volt free relays, but swith the line voltage that is supplied to the Nano IO Air and is powering the unit itself.

In addition 6 digital inputs (24V) are available.