EnOcean Setup

How to start and configure your EnOcean extension

More information about EnOcean

Technical Data

  • 1x EnOcean Transceiver
  • 128 sensors can be learned
  • 128 actuators can be learned
  • Configure with Loxone Config
  • Connection via Loxone Link
  • Dimensions: 34 x 85 x 49mm (2 TE)
  • Power supply 24VDC
  • Power consumption is approximately 30mA
  • Protection: IP20
  • Ambient temperature: 0 to 50°C
Technical Data

Installation

  • Mount extension on a DIN rail
  • Connect 24V DC power supply, but do not switch on until the whole installation is completed
    (We recommend looping the power through the Miniserver)
  • Connect the Loxone Link
  • Note: If it's the last extension, terminate the Loxone Link with a 120Ω resistor
    (Included with the Miniserver)
  • Turn on the power supply
  • After a few seconds, the left LED will flash green if the extension is already configured, or orange if not

Dimensions

EnOcean Extension dimensions

Configuring Extensions

Extensions are connected to the Miniserver with Loxone Link

To add one or more extensions to the program the simplest way is to connect up the extensions to the Miniserver using the Loxone Link and looping power. Then do a search in Loxone Config, which will bring up the Miniserver and all the connected extensions. You can highlight a single extension, give it a name and then click Create device which will add in the highlighted extension. Or you can click on Create all devices which will add all the connected extensions in to the program with the correct serial numbers.

Extensions are not connected to the Miniserver

If there is no physical extensions connected to the Miniserver they cannot be found in the search. However you can add the extensions to the program so you can configure a system before installing. In the configuration software, connect to your Miniserver and download the existing configuration (if there is one) from the Miniserver. Select the 'Devices' drop-down menu on the Periphery tab and select the required extension, then fill in the serial number in the properties.

Entering a serial number

If you are manually adding devices before the Miniserver install has been done, or if an extension has been replaced you need to add the serial number in the properties. Click on the extension in the periphery tree. Enter the serial number of the extension in the properties section. 

Serial number
The serial number is on the back of your extension. You can find the number just below the barcode (see picture).

Save the configuration in the Minisever

After entering your extension's serial number, click on the Miniserver tab and select 'Save in Miniserver'. The controller reboots and after about 10 seconds, both status LEDs on the extension will turn green.

Identify device

If you have installed several extensions of the same type and cannot identify which one is which (for example 2 DMX extensions) then you can use the software to identify a device. Simply click on the device in the periphery tree and the extension will flash red, green and yellow very quickly so you can identify it.

Adding new sensors

Enable Monitor

Select the Miniserver tab and check the 'EnOcean Monitor' box:

Configure the sensor

The EnOcean monitor has two modes, 'Monitor' and 'Learn'. In the monitor, click 'Monitor', this will display each individual signal:

Then click on 'Learn' in the monitor and you will see the signals from the same sensor grouped together with a count next to them. Highlight the sensor, enter a 'Name' and select a 'Type', then click 'Create sensor':

The sensor can now be found in Periphery tree:

The push button in our Webshop is a 2 channel rocker style push button. In our configuration software this is referred to as a push-button (4-way but effective 2-way). 

Configuring a window contact

Identify the sensor by magnetically initiating a change in its status.
Highlight the sensor as before, enter a 'Name' and its 'Type', then click 'Create sensor'.

Configuring a motion detector

Identify the motion detector by repeatedly pressing its configure button.
Highlight the detector, enter a 'Name' and its 'Type', then click 'Create sensor'.

We have a range of motion detectors in our Webshop including a wireless solar PIR.

Adding new actuators

Configure the actuator

Configuring may vary from manufacturer to manufacturer. This guide refers to the switching relay found in our Webshop.

Add an actuator from Periphery tab:

Save the project in the Miniserver:

Pairing with the actuator

Highlight the actuator you have just added and click on 'Learn Device' in the context tab:

1. Push the program button on the relay (LED flashes red).
2. Click 'OK' in the pop up dialog in the Loxone Configuration Software (LED on actuator will go red).
3. Confirm the pairing by pushing the program button on the relay again (LED goes off).
4. Save you configuration in Miniserver again and you are ready to go.

Compatible EnOcean Sensors

The EnOcean extension supports EnOcean wireless sensors which are based on EnOcean technology.

PIR

  • 0 - No one detected
  • 1 - Presence detected

Window Handle

  • 0 - Closed
  • 1 - Open
  • 2 - Slanted

Humidity Sensor

  • 0 to 100%
     

Reed Switch / Contact Switch

  • 0 - Open
  • 1 - Closed
     
     
     

Light, Temperature Presence Sensor

  • Type 1 - 0 to 510 lux, 0 to 51°C
  • Type 2 - 0 to1020 lux, 0 to 51°C
  • Type 3 - 0 to 1530 lux, -30 to 50°C

Light Sensor

  • Type 1 - 300 to 60000 lux
  • Type 2 - 0 to 1024 lux
     
     
     

Room Controllers

  • The EEP number can be obtained from the manufacturer
     
     
     
     

EEP 07-10-01/A5-10-01

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
  • Ventilation: 0 to 255
  • Presence Switch
     

EEP 07-10-02/A5-10-02

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
  • Ventilation: 0 to 255
  • Day / Night Switch
     

EEP 07-10-03/A5-10-03

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
     
     
     

EEP 07-10-04/A5-10-04

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
  • Ventilation: 0 to 255

EEP 07-10-05/A5-10-05

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
  • Presence Switch

EEP 07-10-06/A5-10-06

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
  • Day / Night Switch

EEP 07-10-07/A5-10-07

  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 255

EEP 07-10-08/A5-10-08

  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 255
  • Presence Switch

EEP 07-10-09/A5-10-09

  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 255
  • Day / Night Switch

EEP 07-10-0A/A5-10-0A

  • Temperature Sensor: 0 to 40°C
  • Controller: 0 to 255
  • Input Contact

EEP 07-10-0B/A5-10-0B

  • Temperature Sensor: 0 to 40°C
  • Input Contact

EEP 07-10-0C/A5-10-0C

  • Temperature Sensor: 0 to 40°C
  • Presence Switch

EEP 07-10-0D/A5-10-0D

  • Temperature Sensor: 0 to 40°C
  • Day / Night Switch

EEP 07-10-10/A5-10-10

  • Temperature Sensor: 0 to 40°C
  • Humidity Sensor: 0 to 100%
  • Controller: 0 to 255
  • Presence Switch

EEP 07-10-11/A5-10-11

  • Temperature Sensor: 0 to 40°C
  • Humidity Sensor: 0 to 100%
  • Controller: 0 to 255
  • Day / Night Switch

EEP 07-10-12/A5-10-12

  • Temperature Sensor: 0 to 40°C
  • Humidity Sensor: 0 to 100%
  • Controller: 0 to 255

EEP 07-10-13/A5-10-13

  • Temperature Sensor: 0 to 40°C
  • Humidity Sensor: 0 to 100%
  • Presence Switch

EEP 07-10-14/A5-10-14

  • Temperature Sensor: 0 to 40°C
  • Humidity Sensor: 0 to 100%
  • Day / Night Switch

EEP 07-10-15/A5-10-15

  • Temperature Sensor: -10 to 41.2°C
  • Controller: 0 to 63

EEP 07-10-16/A5-10-16

  • Temperature Sensor: -10 to 41.2°C
  • Controller: 0 to 63
  • Presence Switch

EEP 07-10-17/A5-10-17

  • Temperature Sensor: -10 to 41.2°C
  • Presence Switch

EEP 07-10-18/A5-10-18

  • Light Sensor: 0 to 1000 lux
  • Temperature Controller: 0 to 40°C
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

EEP 07-10-19/A5-10-19

  • Humidity Sensor: 0 to 100%
  • Temperature Controller: 0 to 40°C
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

EEP 07-10-1A/A5-10-1A

  • Supply Voltage: 0 to 5V
  • Temperature Controller: 0 to 40°C
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

EEP 07-10-1B/A5-10-1B

  • Supply Voltage: 0 to 5V
  • Light Sensor: 0 to 1000 lux
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

EEP 07-10-1C/A5-10-1C

  • Light Sensor: 0 to 1000 lux
  • Light controller: 0 to 1000 lux
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

EEP 07-10-1D/A5-10-1D

  • Humidity Sensor: 0 to 100%
  • Humidity Controller: 0 to 100%
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

EEP 07-10-1E/A5-10-1E

  • Supply Voltage: 0 to 5V
  • Light Sensor: 0 to 1000 lux
  • Temperature Sensor: 0 to 40°C
  • Ventilation: 0 to 7
  • Presence Switch

Switch 1-way

  • 0 - Switch Off
  • 1 - Switch On
     

2-way switch (with 1 undivided panel)

  • 0 - Switch Off
  • 1 - Switch On

Switch 2-way

  • 0 - Switch Off
  • 1 - Switch On
     

Switch 4-way

  • 0 - Switch Off
  • 1 - Switch On

Push-button 2-way

  • 0 - Button not pressed
  • 1 - Button pressed
     

Push-button 4-way (with one-piece cover)

  • 0 - Button not pressed
  • 1 - Button pressed

Push-button 4-way

  • 0 - Button not pressed
  • 1 - Button pressed
     

Push-button 8-way

  • 0 - Button not pressed
  • 1 - Button pressed

Temperature and Humidity Sensor

  • 0 to 40°C, 0 to 100%

Temperature Sensor

Type 1 -40 to 0°C
Type 2 -30 to 10°C
Type 3 -20 to 20°C
Type 4 -10 to 30°C
Type 5 0 to 40°C
Type 6 10 to 50°C
Type 7 20 to 60°C
Type 8 30 to 70°C
Type 9 40 to 80°C
Type 10 50 to 90°C
Type 11 60 to 100°C
Type 12 -60 to 20°C
Type 13 -50 to 30°C
Type 14 -40 to 40°C
Type 15 -30 to 50°C
Type 16 -20 to 60°C
Type 17 -10 to 70°C
Type 18 0 to 80°C
Type 19 10 to 90°C
Type 20 20 to 100°C
Type 21 30 to 110°C
Type 22 40 to 120°C
Type 23 50 to 130°C

Compatible EnOcean Actuators

The EnOcean extension supports EnOcean wireless actuators which are based on EnOcean technology.

4BS EEP A5-38-08

  • Dimmer
  • 0 to 100%

RPS EEP F6-02-01

  • Blind actuator

RPS EEP F6-03-01

  • Universal actuator

4BS EEP A5-20-01

  • Valve actuator

RPS EEP F6-02-01 (digital out)

  • Relays
  • 0 - Relay open
  • 1 - Relay closed

Find out more

Contact us

 

Icon config
Installation and Quick Connection Guide (pdf)

Download

tl_files/loxone/design/images/icons/icon_tickmark.png
Extension EG Declaration of Conformity (pdf)

Download

tl_files/loxone/design/images/icons/icon_tickmark.png
RoHS Declaration of Conformity (pdf)

Download